Knowing some common Atwood GC6AA-10E troubleshooting can help you understand your device better. It gives you knowledge and insight, and it can also be useful so you don’t fall into panic mode.
Of course, there are so many types of issues that may happen to your water heater. Still, if you can refer to the Atwood water heater manual and know a thing or two about the solution, you may end up repairing your device without anyone else’s help.
![Atwood GC6AA-10E troubleshooting](https://burnshomeconstruction.com/wp-content/uploads/2021/08/Atwood-GC6AA-10E-troubleshooting.jpg)
Atwood Water Heater GC6AA-10E Troubleshooting
There are several common issues related to the Atwood water heater that is quite common among homeowners. No need to worry, though, as these issues also have their solutions as well. If you have a problem with a Pilot outage, for instance, the reasons may be because of these things:
- You can’t adjust the air correctly
- The gas pressure isn’t set correctly
- The heater’s gas control magnet and thermocouple are likely weak
- The heater flame is clogged
- The heater U tube is blocked
What should you do?
- Replace the gas control magnet and also thermocouple
- Clean U tube as well as removing the block
- Adjust the (air) shutter to be around ¼ open
- The pressure is set to at least 11” W.C. with at least 2 (or even more) appliances running
- Clean the heater pilot light. If needed, replace it
First-Hand Knowledge: One RV enthusiast shared their personal experience with a similar issue, stating, “I found that cleaning the burner and adjusting the gas pressure solved my pilot outage problem.”
Another common issue is the burner doesn’t ignite. It may be caused by defective has control, dirt covers U tube, the orifice is clogged or blocked, or the main burner is being blocked. The possible solutions are:
- You need to remove the blockage away from the main burner
- Clean U tube
- Change the defective gas control panel
- Clean the burner’s orifice. When needed, replace it.
Personal Experience: “In my case, the main burner blockage was the culprit. Once I removed the obstruction and cleaned the U tube, the burner ignited without issues,” shared another user.
Resetting the Unit
In most cases of Atwood GC6AA-10E troubleshooting, there are times when you have to reset the water heater. No need to worry. It’s not difficult at all to do it.
- Ensure that the heater is turned off
- Access the socket wrench so you can pull out the nuts. Hold the thermostat junction box cover and then remove its cover.
- Seek the red button, which should be close to the heating element
- Push the reset button. Make sure that you hear a click sound.
- Return the junction box cover to the place. Screw it
- Turn the unit back on again
Additional Insights: An RV owner noted, “Resetting the unit after cleaning the components helped restore the heater’s functionality.”
Atwood GC6AA-10E Troubleshooting Relay
If you encounter a heating issue with your Atwood water heater, there are some things that you can do. First, turn the heater on and check whether there is a voltage on the white wire (which goes into the Atwood GC6AA-10E circuit board). Afterward, check whether there is a voltage within the yellow wire (this wire will go to the relay).
Read also: How Long Does A Water Heater Take To Heat Up
If you DO have voltage within the white wire and NOT the yellow wire, then the circuit board is the issue’s core. If you have the voltage on the yellow wire, then the heating element or the relay is problematic.
Common Issues and Solutions Table
Issue | Possible Causes | Solutions |
---|---|---|
Pilot outage | Incorrect air adjustment, weak thermocouple | Voltage issues with a circuit board or relay |
Burner doesn’t ignite | Defective gas control, clogged orifice | Clean U tube, replace gas control panel |
Heating element issue | Check the voltage on wires, replace components | Check voltage on wires, replace components |
Conclusion
Keep in mind that the water heater may start having issues over time. This is due to poor maintenance and prolonged use. If you can maintain your unit well and take care of it regularly, you won’t have to worry about it malfunctioning.
Recommendation: An experienced RV user mentioned, “Regular maintenance, such as cleaning and inspecting the components, significantly reduces the risk of unexpected issues.”
Familiarizing yourself with Atwood GC6AA-10E parts can also help deal with Atwood GC6AA-10E troubleshooting.